reballing
The process of reapplying the balls (protruding contacts) on a ball grid array.
282 entries.
The process of reapplying the balls (protruding contacts) on a ball grid array.
To perform a rebatment; to rotate one orthographic view into the plane of another orthographic view along the line of intersection between the two planes.
To transfer (material) from one beam to another by winding.
The practice of transferring identifying parts of a wrecked car (registration plates, compliance plate, etc.) onto a stolen car of the same make and model, allowing the stolen car to be sold with the identity of the wreck.
The process of modifying the bore of an engine.
Abbreviation of rescue, exposures, containment/confine/confinement, extinguish, overhaul.
A contact device installed at an outlet for the connection of an attachment plug (typically by receiving the plug's prongs) to supply portable appliances or equipment.
The act or ability to receive radio or similar signals.
To replace the cable or wire on an electric circuit, typically a high-voltage transmission line, usually to afford a greater electric-current-carrying capability.
To add a new roof membrane or steep-slope covering over an existing one.
The extraction of an ore from a mine, or of a metal from an ore
The growth of grain fragments in an alloy, especially when it is worked by cold rolling.
A card indicating a firefighter's qualifications and specialties.
hydrogen produced by using the waste heat from nuclear reactors to power high-temperature catalytic splitting
An automatic traffic light enforcement camera which captures images of vehicles violating red lights.
A solution consisting essentially of aluminium acetate, used as a mordant in the fixation of dyestuffs on vegetable fiber.
The chemical dezincification of brass alloys, where the zinc in the brass leaches out and leaves behind fragile or powdery copper metal.
To break or crack through brittleness when red-hot; to be red-short or hot-short.
To produce metal from ore by removing nonmetallic elements in a smelter.
A hydraulic device for reducing pressure and hence increasing movement, used to transmit the load from the hydraulic support of the lower shackle to the lever weighing apparatus in some kinds of heavy testing machine.
The ratio of a material's change in thickness compared to its thickness prior to forging and/or rolling.
A device which reduces the input rotational speed to a lower output speed, and can also increase torque.
That reduces a substance etc. to a more simple or basic form.
A form of embroidery done in red thread rather than black.
A comb-like part of a beater for beating the weft when weaving.
Imperfectly welded together in masses of rods.
A device consisting of radial arms with horizontal stats, connected with a harvesting machine, for holding the stalks of grain in position to be cut by the knives.
The degree to which a metal or compound can withstand heat
A metal, such as molybdenum or tungsten, with a high refraction, and hence a high melting point.
The amount of width a woven cloth grows by when the fibers swell, used to determine the width of the reed to use in weaving.
Any of a group of hybrid pelargoniums known for their upright habit and large, showy flowers, Pelargonium × domesticum
Reprecipitated after chemical treatment, especially in the form of fibres; pertaining to fibres prepared in this way.
A form of braking used on some electric vehicles in conjunction with the main braking system, where kinetic energy from braking is converted into electricity and fed back into the power supply by using the traction motors as generators.
A furnace having a regenerator in which gas used for fuel, and air for supporting combustion, are heated; a Siemens furnace.
A tool used to convert the voltage from one region's standard to another.
The inner part of the mould in which types are cast.
A strip of wood or metal of the height of a quadrat, used for regulating the space between pages in a chase, and also for spacing out title pages and other open matter.
To remove the outer surface of, as of an old hewn stone, so as to give it a fresh appearance.
To restore or repair (a vehicle, building); to make habitable or usable again.
Acronym of repetitive electrical impulse noise.
to fill up the joints of, as stones in buildings when the mortar has been dislodged by age and the action of the weather.
An electrical actuator that allows a relatively small electrical voltage or current to control a larger voltage or current.
A room in a railway signalling installation where relays for operating signals and points or switches are housed.
The amount of time elapsed between the moment when the actuating time for release commences and the moment when the braking force ceases.
In a wooden frame: the projection or shoulder around, or at the side of, a tenon (“projecting member made to insert into a mortise”), used to strengthen a mortise-and-tenon joint.
Earth or materials made into an embankment after excavation.
A communication with a data processing facility from a remote location or facility through a data link.
The remote control device used for this purpose.
To cover a wall with a layer of plaster.
A rule describing the relationship between the number of external signal connections to a logic block (i.e. the number of "pins") with the number of logic gates in the logic block.
Steel used to reinforce concrete.
to bring back (something) into operation.
A fabric made of silk or wool, or of silk and wool, and having a transversely corded or ribbed surface.
In calico printing, a design repeated at equal intervals in a pattern.
The amount of time from the application of an excitation pulse to the application of the next pulse.
To replace or repair the pointing in brickwork.
The process of renewing mortar joints in masonry
A code of up to four letters allocated to and used by railroads and other owners of rolling stock for identification purposes, shown on each rail vehicle in combination with an individual number for the vehicle.
In masonry, the return of a moulding in an internal angle.
A method of determining a position by using a map and compass bearings for two additional points.